Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 1 in stock

Modern solid state electronic regulator for models with Bosch charging system

Bolts to original mounting point but this replacement part is not as tall as the old metal regulator. Also known as Guzzi ref. 17703800. Replaces ELA29704

See our Bosch fault finder page for help diagnosing problems on your Bosch charging system. The original type mechanical regulator is no loger available

 2 in stock

29703800-z 29703800 GU29703800 29 70 38 00
 2970 3800 2970.3800 29.70.38.00

Old type 4 pin starter relay in metal case. Note that this has two large terminals and two smaller ones, depending on model you may need to fit wider spade connectors to fit this relay. See ELA10003 for large female spade connectors

 This part is due back in stock soon, call 01484 841395 to reserve yours

 12732500 GU12732500 12 73 25 00
 1273 2500 1273.2500 12.73.25.00

Zadi ignition switch with 2 keys

4 male spade type connectors on underside, replaces original switch with bullet connectors. See ELA10005 for female spade connectors and FRA19741 for rubber wiring boot

 More than 5 in stock

 31735360 GU31735360 31 73 53 60
 3173 5360 3173.5360 31.73.53.60

Also fits Benelli 750 Sei (series 2) - fits with minor modification

Brakelight switch (microswitch) with 2 pin lead

Also see ELA30860

 Availability varies on this part, check availability

 27749815 GU27749815 27 74 98 15
 2774 9815 2774.9815 27.74.98.15

Set of ignition points (made up of two boxes of contacts)

 More than 5 in stock

 19709620 GU19709620 19 70 96 20
 1970 9620 1970.9620 19.70.96.20

12 volt ignition coil for models equipped with points, Bosch or Motoplat ignition systems, includes HT lead. Terminal layout is different to original coils- see photos.

Not for Digiplex models. Also known as Guzzi ref. 19716500, 19716520

 5 in stock

 31716560 GU31716560 31 71 65 60
 3171 6560 3171.6560 31.71.65.60

Right hand Domino type starter switch for use with separate throttle, e.g. Tommaselli twin pull throttles ACA10500 or ACA10501

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. If replacing 'Lego' type switchgear (e.g. Le Mans 2, V50) with integrated twistgrip you will need a separate twistgrip, see ACA10500 and ACA10501. Packaging may include explanation of switchgear wire covers. This type originally fitted as standard to the early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear.. Molex connectors available separately.

 1 in stock

 01738800 GU01738800 01 73 88 00
 0173 8800 0173.8800 01.73.88.00

Brakelight switch for handlebar master cylinder

As this is longer available you may wish to fit BRA01004 instead

 Sorry, this part is no longer available.

 28741100 GU28741100 28 74 11 00
 2874 1100 2874.1100 28.74.11.00

Prolong battery life with this 9 stage smart battery charger, suitable for 6v, 12v AGM and lead acid batteries.

Weatherproof - suitable for use outside 6V / 12V 1A Auto-sensing charger. Suits all AGM, Lead Acid, Calcium and Gel batteries Charges 6v and 12v batteries Ring terminal and alligator clip harnesses included Spark proof Maintains full charge Simple, connect and wait for green light Overload / Short circuit protection See ACA96001 for a spare set of charging leads (e.g. for a separate bike).

 This part is due back in stock soon, call 01484 841395 to reserve yours